PDA

View Full Version : Electronics and Triggering



kev
10-15-2005, 07:00 PM
General Electronic Stuff

Equipment for live situations (http://www.pearldrummersforum.com/showpost.php?p=1850691491&postcount=2)
Great to-the-point info about the pros and cons of triggers and mics (http://www.pearldrummersforum.com/showpost.php?p=1850752414&postcount=3)

Recording

Lots of information on home recording (http://homerecording.com/bbs/)

Triggering

Tips for when you're running triggers (http://www.pearldrummersforum.com/showpost.php?p=1850809418&postcount=3)
What is Triggering? (http://www.pearldrummersforum.com/showthread.php?t=108061)
More 'What is Triggering?' (http://www.pearldrummersforum.com/showthread.php?t=116772)
Methods of Triggering (http://pearldrummersforum.com/showthread.php?t=106411)
Is is possible to use triggers while having dynamics? (http://www.pearldrummersforum.com/showthread.php?t=133798)
SLIPKNOT1's cut on triggering (http://www.pearldrummersforum.com/newreply.php?do=newreply&p=1849957386)

Miccing Drums

Lots on informatiion about miccing on a budget (http://www.pearldrummersforum.com/showthread.php?t=79459)
Nils project on "correct micing, interference and impulse widening" (http://www.pearldrummersforum.com/showpost.php?p=1850085550&postcount=4)
Bass Drum Miccing (http://www.pearldrummersforum.com/showthread.php?t=108529)
Opinions on mics to use (http://www.pearldrummersforum.com/showthread.php?t=115024)

Monitors

In-Ear Monitors (http://www.pearldrummersforum.com/showthread.php?t=108601)
Opinions on Westone and Shure in-ear monitors (http://www.pearldrummersforum.com/showthread.php?t=116203)

johnboylol
04-14-2006, 06:39 AM
cool man thanks

mf daniel
04-14-2006, 06:14 PM
God, this section rules.

DrummerMom4571
05-28-2006, 09:25 AM
DIY ETube by P-Fozz

I found direction on how to build an etube (same as a Pintech Dingbat)

I made the diagram but the directions are from P-Fozz.


This is the cheapest and the easiest way to build a drum trigger. It works great for Splash and Chinese cymbals.

You need :

- Can of KrylonŽ brand spray paint for plastic (If you want to paint it)
- 15cm of PVC pipe.
- foam.
- a piece of foam rubber sheet.
- Radio Shack Piezo Transducer (273-073A)
- Radio Shack Shielded Phono Jack (274-346)
- end caps to fit tube


What you've got to do :

1. Remove the piezo from its plastic case.
2. Replace little red and black wires by some strong audio cable.
3. Fix the piezo inside the pvc pipe with some double-sided foam tape.

4. Put 'the most you can' foam inside the pvc pipe so the piezo is compressed between this flexible material and the foam tape you set it on.
Put the piezo inside the PVC... It's fragile and you don't wanna damage it... The PVC is to protect it... Technically.. You can put a piezo on just about anything and make it work.. Some designs are better than others...

Piezo's take a better signal placed horozontal..

5. Fix a piece of foam rubber on the outside of the pcv pipe using some double-sided tape (the one we use for carpets)

6. Solder a plug to the audio cable.

You've got your E-Tube !

440561
08-29-2007, 03:16 PM
Great thread - much needed info! thanks